REMOTE START & STOP
REMOTE START & STOP
HI-TECH VACUUM
The kit allows the automatic switching on and off of the vacuum cleaner simultaneously with the machine tool when they are connected. This can occur in three different ways:
a) The vacuum gets switched on by contact without electricity “potential free contact”.
b) The vacuum gets switched on with a 24V contact.
c) The vacuum gets switched on with a 230V contact.
ADVANTAGES
- Energy-saving, as the vacuum cleaner is switched on only when the machine is working.
- Noise level reduction, because the vacuum cleaner is on (and makes noise) only when the machine is working.
- Optimization of operators’ time as one no longer needs to personally attend to the machine in order to switch it on or off.
ANTI-FIRE KIT
AccessoriesHI-TECH VACUUM
This accessory is a device that automatically intervenes in the case that there is a consistent increase of the temperature inside of the collection tank, emptying a mix of air and water inside the tank through a spray nozzle. In the case where the system is not automatically activated, it's possible to activate it manually using the appropriate button.
FILTER
AccessoriesHI-TECH VACUUM
The classification filters for vacuum cleaner and powders emissions into the environment, is assigned by the type of powders and the degree of danger to health. For its suction devices such classification is regulated by IEC 60335-2-69 worldwide. This classification provides several categories of powders, such as: • Category of powders L (low/moderate): fall into that category powders with MPC values (maximum permitted concentration in the work place) > 1 mg / m³Are retained at least 99% of particles aspirated.The disposal of the collected material must be made trying to raise a few powders. • Category of powders M (medium): fall into that category powders with MPC values (maximum permitted concentration in the work place) > 0.1 mg / m³ and wood powdersAre retained at least 99.9% of particles aspirated.The disposal of the collected material must be made trying to raise a few powders. • Category of powders H (high): fall into that category powders with MPC values (maximum permitted concentration in the work place) < 0.1 mg / m³, with carcinogenic and pathogenic powdersAre held at least 99.995% of particles aspirated.The disposal of the collected material must be done without raising powders. On each iVision vacuum cleaner is applied a label indicating the hazard class of the dust in the environment allowed.
LIFT KIT
AccessoriesHI-TECH VACUUM
The lifting device is used for emptying the 100 Lt (iV2 model) or the 160 Lt (iV3 model) chip container with the use of a forklift. The operators do not have to make any effort for the emptying process. At the sides of the collecting containers there are two hooks for the lifting kit to be connected to, which in turn is lifted from the truck by a chain.
TOUCH SCREEN
AccessoriesHI-TECH VACUUM
The vacuum cleaner is equipped with a touch screen unit on the front. It allows the operator to quickly and easily monitor the level of contamination of the filter. Thanks to such a device, the operator is able to recognize in real time the filter condition and the efficiency of the whole vacuum cleaner. Afterwards, the operator can choose to clean the filter (in manual or automatic mode) and also manage the remote Start&Stop control option. Once the filter is completely clogged, the unit will automatically warn the operator of the need to replace the filter utilizing: • A visual signal
AERIAL ARM
AccessoriesHI-TECH VACUUM
The aerial arm is highly recommended for every CNC router. The use of this system reduces the risk of accidents due to obstruction of the tube on the sides of the machine.
SPECIAL KIT FOR FLOOR CLEANING
AccessoriesHI-TECH VACUUM
For floor cleaning, iVision has developed a specific kit with a fixed brush positioned on the front part of the vacuum with a handle for manuevering.
CLEANING KIT Ø 70 mm
AccessoriesACCESSORIES KLEANING KIT Ø 70 mm
The cleaning kit, usable through the IV3 series, consists of a robust, anti-abrasion tube that ends at the extremities with special zinc-plated steel accessories capable of transporting, without any obstacle, chippings and oil from the machine tool to the vacuum collection tank. The suction tube comes housed inside a support in order to facilitate the movement of the vacuum in the workshop without being an obstable for the operator, it allows the avoidance of leakage of oil during the maneuvers of the vacuum.
DRAIN TAP
AccessoriesHI-TECH VACUUM
When customers use the vacuum cleaner for chip and liquid suction operations, they usually purchase the liquid – metallic mesh chips separator from lubrication as an optional accessory. In addition to this accessory, a drain tap is very useful, because it allows draining liquids from the bottom of the tank, without any effort by the operator. Metallic mesh chips separator from lubrication.
EMPTYING ROTARY VALVE KIT FOR CONTINUOUS WORK
AccessoriesHI-TECH VACUUM
For those that need a continuous work cycle in construction environments and need to empty without interrupting work due to turning off the vacuum to empty the collection container, the iVision rotary valve kit is an interesting solution.
ANTISTATIC KIT
AccessoriesHI-TECH VACUUM
To be applied to all models of industrial vacuums in production. This kit allows you to unload electrostatic charges accumulated during the collection phase, avoiding transferring them to other machinery or operators. It’s particularly recommended during the working of aluminum, considering the chips of this material can create a potentially explosive atmosphere inside of the tank.
ADDITIONAL DUMPSTER
AccessoriesHI-TECH VACUUM
In the case that the vacuum cleaner standard capacity 42 Gal is not enough, iVision offers its customers additional high-capacity chip containers. Ivision has developed 2 types of dumpsters: A) 1000 Lt dumpster with automatic opening B) 500 Lt dumpster with manual opening The dumpsters are equipped with a visual filling indicator that shows the operator when it is time to empty the container.
